F2150 manual

Symptom The error message "No card echo" is present in the Single master box. Physically not existing MP-interface card. Please verify the plugged PCD7. F card into the module. For the correct handling of the new flash modules PCD3. Rxxx an and the PCD3. Unfortunately this check can cause problems on older hardware versions if more than two PCD3.

Cxxx modules extension cabinets are used. Symptom The communication module PCD3. F as well as memory modules PCD3. Rxxx do not work when more then 2 extension cabinets PCD3.

Cxxx are connected to a PCD3. It is possible that the same PCD3 was working correctly but after an update of the PCD firmware this symptom appeared.

In this way it is possible to avoid e. Also flash modules can be identified properly before accessing their content. Cxx0 are connected to the PCD. Solution Upgrading the CPLD version will solve the problems as the modules will correctly be recognized by the firmware.

No further action is to be taken. F1xx on slot 0 and also newer intelligent modules like per example the new flash moduls PCD3. The update can be done with the "Firmware download Assistant in the following ways:. Rxxx are fully supported without restriction. But note that the S-Bus full protocol is not fully applicatively due to the reason described below! F, PCD3. F, PCD7. F or PCD7. F from RS to RS, the following code lines are to be used:. As commented, this code is placed into the startup program block XOB 16 and will cause the port to work in RS mode.

This means that it is only possible to use this port after the XOB 16 has been executed. This restart will reset all communication ports and the concerned port will not be in RS mode any more. The PCD is to be restarted manually for establishing the communication again! The same problem occurs after every restart command executed by PG5! This is why the RS is not really applicatively for real S-Bus full protocol actions.

However, there is not problem in using all command except of the restart and of course the S-Bus reduced protocol will not cause any problems.

On some PCD3. F modules the label with the connection diagram do not correspond to the manual. It is wrong. The PCD7. F is the successor of the PCD7.

The main difference are higher baud rates supported by the PCD7. Why was the PCD7. F replaced? When introducing the systems PCD2. M and the PCD3 systems also support for higher baud rates has been introduced.

Unfortunately the PCD7. F couldn't handle the maximal baudrate supported by the new systems. In order to take advatage of the higher baud rates also a new module for the RS interface had to be introduced. This new module is the PCD7. Is the baud rate limitation the only difference? No, there is another difference between the modules. F requires a special 9V power supply from the device on which it is mounted. F doesn't require this additional power supply any more.

M is done in PG5 2. On the properties of the PCD7. Normally, there is no given function to know in the PG5 application program if the BACnet stack is running or not. So, at startup this function could provide a wrong information. The workaround is: 1. If the BACnet Stack is not running or stops, then the counter will not be incremented.

The PG5 2. The project can be used on PG5 2. Due to an error on the PG5 2. Error description: Due to an error on the PG5 2. The error consists in the fact, that on PG5 2. Error correction: The error will be fixed in PG5 2. PG5 2. Workaround for PG5 2. To control the communication mode as described above, 1 additional register must be defined and set to the corresponding value. A 2 nd register can be used to get the current communication status.

Good to know: DDC Suite 2. All Fboxes switch to a fallback mode without using BACnet. Reason: The reason is because of the missing symbols for the new monitoring object inside of the Fbox. During the update of the Fbox, these symbols aren't created automatically. Because of that, the control function of this Fbox does switch off BACnet because of the missing feedback.

Solution: Add manually the symbols with a rightmouse click on the Fbox and click on "Add predefined symbols". Click "ok" if a small window appears. If you have to analyze an Ethernet Network, you have to connect the monitoring PC between the communicating devices. The easiest way to realize that is with a hub which are no more available or with a switch with a special monitor port. The solution is to use a switch with a monitor port.

Any communication over this switch is mirrored on this special port like a hub. You have to connect your analyzing PC to this monitor port and you will get all the traffic which go over this switch. This smal switch has 5 ports, one of them is the monitor port. It is easy to configurate with a Web-interface. See also FAQ Furthermore there is a line to write in a description for more detailed informations. The length of the BACnet object name and the description is restricted from the compiler to signs each.

You can find more information about restrictions and rules in the attached pdf. Reason When writing a persistent value to BACnet and if the "PCD input reference" is used, the configuration stored in the flash memory is destroyed with firmware version previous to 1.

This firmware can be downloaded from the support site. R was created containing BACnet firmware 1. The main reasons for this new firmware are listed in this FAQ. Remark Please note that the BACnet 1. Changes between BACnet firmware version 1. For more information about the changes, please refer to the online help of the BACnet Configurator distributed with PG5 2. Please makte sure that the device you want to alarm supports this Restart Notification available since standard addendum b.

It's "1" for a cold start power on the PLC and "2" for a warm start restart after progrm download. The first 2 characters denote the object that caused the error. If these characters are s, the error is a general stack error in general, due to a misconfiguration.

The rest of the string expresses the numeric code of the object or the error that has caused the failure. Object identifying characters The first two characters can be found in the list below and indicate the object that caused the error:. It is not caused by an object, but rather by a misconfiguration or other error. When using the FBox "Motor 2-speed 2. Symptom When using the FBox "Motor 2-speed 2. Solution The versions listed below correct this wrong behaviour.

Please update your library and then rebuild and download the program again. Firmware versions before the version 1. This phenomenon is observed when a telegram is lost. This telegram loss is random, dependent on the network load. Reason Firmware versions before the version 1. In case a telegram was lost due to network problems the transfer was interrupted by the PCD firmware.

Because of the interruption the BACnet firmware was not notified, but it remained in a state of waiting for the completion of the upload process. Solution The firmware version 1. M5 together with the BACnet firmware 1. R56x to the mentioned or later firmware versions. R65x or PCD3.

R56x is plugged. If the BACnet task is not running e. R65x is not compatible with the PCD firmware the program will not work correctly. This limitation is caused by the rather high usage of ressources performance and memory from both these firmware extensions.

While there is no problem to run one of these firmware extensions, the currently available PCD systems do not support both firmware extensions at the same time. Why is this schematics printed in the System catalogue? The aim of this schematic is to show that both protocols are supported, but not to indicate that both protocols can be used at the same time. The currently only solution is the realisation with two systems, which could e. Mxxx0 or a PCD2.

M5xx0 and a timezone has been configured, the time stamp of an S-Web alarm has an offset to the PCD time. The offset is depending on the time zone configured in the BACnet configuration.

M5xx0 is 1. If you want that the time of the alarms corresponds to the time of the PCD this Container should be set to 0. The PCD3. Mxxx0 or the PCD2. M5xx0 firmware required is 1. As a rule of thumb it a PCD2. Please note that in case a PCD2. Additionally the required memory of e. Several tools are available for BACnet testing purposes. This FAQ lists some free and commercial tools we recommend. Actually most programming and configuration work is done at the office, where testing with "real" systems is often impossible.

Fexible, yet easy to use program for evaluating, analyzing and testing BACnet systems. Commercial tool, which runs under Windows only. Single and multi-user licenses available. Details at www. Commercial usage requires license dongle. Without dongle, the software runs in a limited mode, which stills allows searching for OPC clients and monitoring some objects!

Allows reading and writing property values. Point lists can be saved in XML files. Very helpful for testing purposes during configuration and commissioning BACnet systems. Deatils at: www. Commercial tool, license dongle needed. See Wireshark for a free, open-source alternative to BAS-o-matic. Wireshark Protocol Analyzer Open Source Free, open-source, industrial-standard protocol analyzer with support for hundreds of IP-based protocols.

Details and Download at www. To be continued. Priority 6 is reserved for time operations for BACnet objects like minimum on time or minimum off time. Therefore you should not use this priority. They cannot be imported. You can ignore the error messages and work with the Standard objects which are imported correctly. There are some problems with EDE files of a few manufacturers, because they are not in the right format.

If you have an Excel file with 4 tables Siemens uses this format you have to extract the 4. Take care that the Version of Layout is containing a valid number. If this line is empty try to put in a 2 with a Text Editor and import again.

If the. These Objects are inside of the property "List of Object Property Reference" and can be inside your controller or can be in external controllers.

If you write to Objects in foreign controllers they have to be writable as well. R56x or a PCD7. R56x plugged. The download of the program is aborted with the following message: "NAK Response, failed to write downloadable files.

Missing Flash memory? R56x or PCD7. M5xx0 firmware 1. It is an older software version which can be operated only on certain now no longer commercially available products.

English German. Introduction The communication modules PCD2. Modules for the PCD1. M2 and PCD2. M5 PCD2. F up to devices Modules for PCD3. Mxxx0 PCD3. F up to devices. F2xx - Communication modules ENG Product sold without warranty: This product was sold by a reseller.

Any warranty support needed would be completed by the reseller that sold the product. The serial number provided does not match the previously selected product. It matches the product:. Please return to the product information page and verify the numbers provided or try again later. Errors can be displayed in many formats. Please include all extra characters, such as hyphens or colons or periods as they appear within the number.

Possible error formats where 'x' could represent a letter or number : xx. One or more of the values entered is not permitted. Please wait while we process your request. This process can take several minutes depending on the number of warranties being checked.

Select registration option. Error: Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions.

HP Customer Support. Select your model. How does HP install software and gather data? Search all support. Search help. Tips for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number.

Loading Results. Facing print or scan issues after upgrading to macOS Catalina Search help. Tips for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number. Loading Results. Facing print or scan issues after upgrading to macOS Catalina Apache Log4j Update Please see this document here for current information regarding the Apache Log4j vulnerability.

Need Windows 11 help? Already have an HP account? Select from the products you own. Choose a different product series. Warranty status: Unspecified - Check warranty status Manufacturer warranty has expired - See details Covered under Manufacturer warranty Covered under Extended warranty , months remaining month remaining days remaining day remaining - See details Serial number: Product number: Warranty end date:. Warranty status types. Warranty types. Verify product. It matches the product: Would you like to view the product details page for the new product?

Unable to determine warranty status. We are unable to determine your warranty status for the product and serial number provided. Change your product. Example error formatting. Select a location. Europe, Middle East, Africa. Asia Pacific and Oceania. Select a language. Confirm Back. Check your warranty.