2wire 2701hg-b instruction manual

Not sure if they can change it but looking up the default gateway ip address will give you the router ip address if DHCP is being used and if it has changed somehow? Broadband Link Tab Broadband Link Tab This chapter describes the 2Wire gateway Broadband Link features, and provides detailed instructions on how to customize your broadband settings.

Allowing Inbound And Outbound Traffic If you configure the firewall mnual block an Inbound protocol, you may disable support for hosted applications that require that type of protocol.

If you have performed a reset of your HG-B device or not changed the defaults, you should be able to access it with the following settings:. Informational only—the event does not imply a threat to network security.

Dependent on the hg-b line configuration. Modifying the settings on this page can impact the ability of computers on the local network to access the broadband connection. Table of Contents Add to my manuals Add. Click the Add a new user-defined application link. Your can reset your 2Wire HG-B in the following way s:.

Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you msnual this issue over the phone in a minute or two. Most ISPs provide modems that are configured solely for their service. Posted by mbaurhyte on Mar 17, It is worth reading more about how to reset routers with the 30 30 30 reset and what the risks and considerations are when resetting your router this way, instead of just rebooting it.

Channel 6 is the default, and allowing both to compete on the same channel is a bad idea — give each its own wi-fi channel. Then plug back your router and wait 1 min. Lately during the filling cycle water hammer is occurring. You can configure the firewall to provide advanced security features, including stealth mode, strict UDPor block pings.

When in stealth mode, the 2Wire gateway firewall does not return any information in response to network queries; that is, it will appear to the hacker who is trying to access your network that your network does not exist.

IP address for example, If you enable Block Ping, your network will block all ping requests. Strict UDP instructs the 2Wire gateway to be more restrictive about what packets are allowed to transmit over an established connection from a local network computer to the Internet.

In addition to relying on information about the destination 3-tuplethe 2Wire gateway will also use information about the source of the connection 5-tuple. If you configure the firewall to block an Inbound protocol, you may disable support for hosted applications that require that type of protocol. To block an Inbound or Outbound protocol: Not a start session packet — drop packet. ICMP destination unreachable — terminate session.

To disable attack hg-g for a specific port: The Management and Diagnostic Console provides information about the status of the 2Wire gateway, its broadband network connections, attached home networking devices, system and manuaal information, and a running log of any error conditions.

The link manyal that display are dependent on the 2Wire gateway model. Troubleshooting pages allow you to view detailed logs that maintain a record of all significant 2Wire gateway events, and to perform diagnostic tests. Configuration Key Code The key code associated with the current provisioning settings.

The value is Unprovisioned if the 2Wire gateway has hg-h yet been provisioned. Subnet Mask The subnet mask to be used by the 2Wire gateway on the broadband link. Gateway The IP address of the default gateway default router that The current downstream and upstream noise margin in dB. The current downstream and upstream DSL attenuation in dB.

The current downstream and upstream DSL transmit and receive power in dB. Transmit The cumulative number of cells transmitted, and the number and percentage hg-g in error. Loss of Signal Failures The number of DSL loss of signal failures since the 2Wire gateway was last restarted, and the elapsed time since the last loss of signal failure.

Corrected Blocks The number of corrected DSL superframes that had data errors detected during reception. Modifying the settings on this page can impact the ability of computers on the local network to access the broadband connection. If the value is between 1 to minutes, the PPP session will timeout if the manuaal gateway does not detect outbound traffic destined for the Internet in the specified time. Mabual the 2Wire gateway detects outbound traffic, the session is reestablished.

You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website.

These cookies do not store any personal information.